on 09-12-2020 18:59
Anyone else had this recently?
My HUB 3 updated last night.
on 07-01-2021 18:06
IPv6 maybe?
on 08-01-2021 09:35
I'm struggling to login to my SH3, receiving the following message: "Someone else is currently logged into the settings page. Only one session at a time is allowed. Please try again later."
I checked the logs and that someone was me, nearly 24 hours ago!
on 14-01-2021 06:44
This new firmware is rubbish, I run 2 hub 3's in different locations, the one hub got this update way before the other and I thought issues I saw with that one and still do where related to local area or hardware fault but now I've had this new firmware a week I've noticed some changes here.
Main concern is the increase in jitter, its showing on my BQM's which suggests to me some additional resources are being used, this theory is backed by the following,
I've performed factory reset but as I guessed not changing anything, may I also advise that current setup is Hub 3 (router mode) Gigabit wired Desktop and 1x Wireless Device (Pixel 4a) (no other devices connected)
on 26-01-2021 19:24
Hi all,
I recetly upgraded to vm 350mb from vm 200mb vm hub 3. The hub has been reset to factory and I fnd with the vm spped test using a pc connected via ethernet download speeds of 85mb.
House has had vm cable since it was ntl (white wall boxes say ntl).
Any suggestions to get fastwer downloads speeds.
pc win 10 latest version 12gb ram
regards
Robert
26-01-2021 19:30 - edited 26-01-2021 19:31
@robert_fernando wrote:Hi all,
I recetly upgraded to vm 350mb from vm 200mb vm hub 3. The hub has been reset to factory and I fnd with the vm spped test using a pc connected via ethernet download speeds of 85mb.
House has had vm cable since it was ntl (white wall boxes say ntl).
Any suggestions to get fastwer downloads speeds.
pc win 10 latest version 12gb ram
regards
Robert
Check the 'Connected Devices' section on your HUB.
You may find your wired device's 'Speed (Mbps)' value is '100', rather than '1000' due to:
on 26-01-2021 21:04
@Anonymous wrote:Anyone else had this recently?
My HUB 3 updated last night.
Both my Hub3’s were updated via NMS on 15th Jan and no problem with obtaining 200/20 on my v10 version and also350/35 both with my 2015 iPad Pro @ 13.7 iPadOS.
However my new iPad Pro(4th gen) @ 14.3 iPadOS will only connect to my 350/35 v1* hardware version despite playing with PRIVATE ADDRESS turned on or off on 200/20 Tier connection. Since I no longer have access to trials forums I cannot publically reveal further information of my V1* VMDG505 Hub! (Even though it’s released in public domain since early 2019 )....... 😞 ......... unless @Kev_B gives me explicit written permission. 😜
on 27-01-2021 22:28
Was updated recently, but I run in modem mode with Ubiquiti USG-Pro-4 router and WAPs. No problems noticed.
on 28-01-2021 08:56
@Tudor wrote:Was updated recently, but I run in modem mode with Ubiquiti USG-Pro-4 router and WAPs. No problems noticed.
Can you confirm your VMDG505 hardware version please?
on 28-01-2021 14:33
As copied from hub page:
Standard specification compliant | : DOCSIS 3.0 |
Hardware version | : 10 |
Software version | : 9.1.1912.304 |
28-01-2021 18:06 - edited 28-01-2021 18:09
@Tudor wrote:As copied from hub page:
Standard specification compliant : DOCSIS 3.0 Hardware version : 10 Software version : 9.1.1912.304
Thanks- was hoping you had newer hardware. I’ll have to do it the hard way long & torturous ....... cheers anyway.