Hub 3 - Solid Red Light
As the title explains, my Hub3 router is showing a solid red light. Weirdly, internet is stable. It's in a well ventilated place and doesn't appear to be hot/warm to the touch. I've tried powering it off/on again (even left it off overnight), full unplug and a factory reset. The solid red light returns. Please advise.Using Deco S4 with TP Link Archer AX72
Hi, I've got my Virgin Media Hub 5 in Modem mode and have connected my Archer AX72 router to it. The AX72 router is in my office and hardwired to my PC and console and all other devices are connected via Wi-Fi from the Archer AX72. I want to connect my cable box and TV in my living room via ethernet. Can I buy the S4 an connect it to my AX72? If so shall I have the S4 in Access mode or Router mode? Will the devices around the house still work via Wi-Fi from the Archer or will I need to connect to the Wi-Fi on the Deco S4? Kind of new to these things so any suggestions and help would be appreciated. ThanksRouter requires resetting weekly
Good morning, I've tried call the virgin media phone line but get locked into a never ending cycle with the bot. Basically, swapped to virgin about a month ago and ever since we did the router disconnects all connected devices roughly once a week. The fix isn't difficult, we then have to unplug the router and let everything reconnect - not awful fix but very inconvenient especially with how much were paying! How do we fix this?Modem Mode stopped working since Tuesday's outage (Hub 5x)
I managed to painstakingly get it to work a few weeks ago with my Unifi Express 7 but last night after a brief outage it has stopped passing a WAN IP to the Unifi Router. I've spent hours and hours trying every variant of the Reddit threads and forum posts on how to enable it and it WILL NOT for the life of me pass an IP Address to the WAN Port once it's in Modem Mode. What I did last time was the following: Connect the Unifi Router to Hub Port 1. Connected to the Hub portal 192.168.0.1 via a laptop connected to the Unifi Router LAN. Disabled DMZ, WiFi, Firewall, UPnP and DHCP. When I disable DHCP it annoyingly drops the lease on the Unifi Router so I then have to connect my laptop directly to the 10gig service port on the Hub and change its IP to be under the 192.168.0.x subnet. I know of no other way to connect to it (other than forcing a static internal IP on the Unifi WAN port which also fails). Enable Modem Mode and unplug the laptop from the service port before it reboots. Not sure if the laptop unplugging is what made it work but I've tried both removing and leaving it in today. Power Cycle the Hub after it reconfigures. I am completely lost and it has failed constantly the last few days.
Problems: Adding a 3rd Party Router: ASUS RT-BE88U
Good morning all, I trust that you are well. I would like some guidance, please, on setting up my new router. It has been a while since I've been in the community, and the format has changed quite a bit! So, I've yet to really explore to see if the solution is already posted in another thread - will do that next Existing Kit: I have a Superhub 4 (SH-4) with the 1-GB service. Sadly, I am not in the 2,5 area, not that my needs justify the expense. I have logged on and placed the SH-4 into Modem mode, and when I connect to any of the ports directly with the Mac, I can log in via 192.168.100.1 as well as being able to access the 'net. So the SH-4 appears to be working in modem mode; as far as I can tell; oh, yep, the annoying LED strip is in green mode. ASUS Install: Yesterday, I connected my new router using the 2.5 WAN port on the Asus, connected to port 1 on the SH-4, and after configuring the router, it seemed to work, the WAN light on the ASUS was lit white-blue and all seemed to be fine and dandy. I then, after tinkering with something (tbh can't quite recall but I think it was binding two inputs together for my NAS)) and it required a reboot. After which the WAN lignt on the ASUS has been lit up in red, and I am unable to access the 'net. Even after rebooting and a factory reset, the WAN light is nearly always red. A couple of times, it has been white, but I still can't access the internet. The error message from the ASUS suggests a DHCP issue. I'm back on the SH-4 in router mode currently. Does anyone have any ideas/suggestions on what I should try next, to resolve this issue? I really appreciate any help you can provide.Drop in speed from Hub 3 as router to TP Link
Hi all, I have VM 250Mbps package with Hub 3. When using the hub as router I am getting 250Mbps+ speeds, no issues. When using my TP Link C7 AC1750 router and Hub 3 in Modem <ode, the WiFi speed drops to 100Mbps. I am using good quality (based on reviews?) ethernet cable to link the two (Cat7). TP Link C7, I believe, has sufficiently fast internet port to take the 250Mmps from Hub 3, so this shouldn't be an issue either. I also have 3x mesh devices (TP Link RE450), but I don't thinks that's relevant here. What do I need to do to get my TP Link router do 250Mbps, instead of the 100Mbps..?
Pod is dead
Hi everyone My WiFi pod has suddenly ceased to function, I've gone through every diagnostic I can think of, I work in the IT industry so have a decent track record. It appears to be the power supply, but I could be wrong? Is there anything I can do to avoid talking to "Customer Service"? I am considering replacing the hub at the moment, modem mode. But the ones I like are quite expensive. Couldn't connect via Virgin Connect app, it just keeps crashing. I'm current on 1GB, any suggestions would be most appreciated. JonathanRaspberry pi as add-on router
I am connecting a Raspberry pi (4 Model B, with wifi software) with the VM router via Ethernet cable. Available Wifi networks does show the new network, I can enter the (correct) password, but it always shows "Can't connect" to the network. I discussed numerous option with the raspberry software provider. This problem is unknown. I see in this forum that other users had to call the Internet Service Provider to clear the connection before using their own router. I notice that under Tools / Network Status has "Downstream channel Locked" (same for Upstream) No filter to exclude any IPs / MAC. What needs to be done to connect through the Ethernet-connected Raspberry add-on router?
