Hub 5 Firmware Upgrade
Had a Firmware upgrade pushed out this morning at 00:17 Service was resumed about 6 minutes later according to my Router emails. Now at LG-RDK_7.6.15-2306.5 No idea what the changes are however as...
Forum Discussion
I had an engineer out to look at this and, naturally, they were unable to fix it. VM's support were not any help either.
I ended up spending a lot of money and found that the TP Link unmanaged network switch - 8 port works. It was trial and error. It was the third one I tried and was pure luck that it worked. I had no idea about it being the EEE until I found/was directed to an article about the port breaking due to the firmware update. The engineer pointed me at it about a week after his visit. At least he cared.
I am now raising a complaint because I've had to spend way too much money to get a working network.
"I am now raising a complaint because I've had to spend way too much money to get a working network"
While I totally sympathise with you I think it’s will be a waste of time and effort doing a complaint. VM guarantee you a broadband connection and they have fulfilled their part of the contract. Time and time again it has been mentioned on the board that in no way do VM support and equipment connected to their connection that they have not supplied.Bit like saying water is supplied but if it poisons you not anyone's problem because the water was supplied.
No one is asking them to diagnose or fix equipment they haven't supplied though - it's their own router that is currently broken and doesn't respect the ethernet spec in regards to EEE implementation. So of course the complaint is entirely valid - I'd go as far as say it could be misleading advertising, as the SuperHub 5 is advertised with having a 2.5Gb port, and that port is not spec compliant as it is right now.
If you use the Test via the App, Virgin Guarantees the speed to the Hub. What you get out the other side is down to what you connect to it.
About 14 years ago, I was advised by a network fitter, that using routers as WiFi access points connected by cat5e cable to the hub was the best way to eliminate WiFi dead spots. I only used the Hubs WiFi to manage the hub. Later I was told about using Switches to improve my network.
After discussing this recently, with Network Nerds, whom suggested my bottleneck of using 1 gig switches was why I could only get 960 download at my devices. I then got a 2.5 gig switch and then I got the same speed to my devices with a 2.5 gig port.
This is the Virgin recommended speedtest via SamKnows.
The supposed “benefit” that attracted me to using VM is that they supply a Hub with 2.5G Ethernet AND a set of wifi access pods for full home coverage, WITHOUT needing to spend any more money. I verified that the pods work using Ethernet backhaul when connected to the hub (via a switch to allow multiple connections to the 2.5G Hub socket). The pods work with the Hub to allocate the best connection to each device with minimal interference. This actually works perfectly for me and I get great coverage everywhere in the house (and even outside). If you try to introduce ANY other wifi component into the mix, the intelligence of the pods working with the Hub will deteriorate. If you decide to use your own equipment you will not be affected by this issue, but as I said at the beginning, the perceived benefit was to not need to.
Hence, VM need to fix this issue, else their hardware offering is pointless when on the Gig1 service.
I am currently on the old firmware version before this issue occurred, so all IS working ok for me. But I’m told that potentially the broken firmware could be rolled out again, as I’m on a lower version than their system expects.
I’ve also been told that testing with the “LG team” is ongoing and they are close to a fix. I don’t know what “close” means, so I’ve asked someone from VM forum team to make a statement here to update everyone and not just me directly.
I would advise anyone having this issue to raise their own post, and you may then get a direct response via a private message, from which you can make your own enquiries.
Have been discussing this for the last few weeks on Discord, with the nerds from a leading PC magazine. To Negate the Energy Efficient Ethernet, you need a Managed switch, to prevent devices being switched to a low power state. You also need to check the Ethernet device on your PC / Laptop has EEE turned off. I got 2 switches that came supplied with this off by default. A 8 port 2.5 GBit one (£99 less £60 refund for an unmanaged I returned) that is connected to the Hub5 2.5 port & a 16 port 1 Gbit one (£64 the one I relplaced was transferred to the other end on my 20 meter cable runs to replace a 4 port switch) connected to port 2 of the hub. I route traffic according to the speed of the devices in use.
It is my choice to spend the funds, but the upside of this, is I can now get download speeds, that I am paying for, after 18 months of 960 mbits max. Even though I had a PC with a 2.5 Gbps port connected to the 2.5 Gbps port on the Hub 5, via a 2.5 Gbps un-managed switch :-
