Forum Discussion

Scousedicko's avatar
Scousedicko
Joining in
3 years ago

Wi-Fi pod flashing blue

After having issues with my broadband the other day and eventually it sorting itself out I have found my Wi-Fi pod is just continuously flashing blue.  I’ve tried resetting the hub, switching off pod and even moving it to same room as my hub.  However it’s still starts with green light then goes to to constant blue light flashing.  I’ve tried the set up tools on the app and it says no pod detected.  Any advice would be appreciated.  Thanks 

  • Just an update, after flashing blue for probably 10 minutes the light goes off and then goes green again to start the same cycle over again like I’ve just plugged it in and switched it on.  Also when I go onto the connect app it doesn’t show any connected pod and when try to add one it says none detected.

      • Scousedicko's avatar
        Scousedicko
        Joining in

        Hi,

        yes I have received the new pod which is working fine however I have tried everything to get the original one working.  The only way it works now is to connect it via Ethernet cable.  Once unplugged it starts with the green light then goes onto a blue flashing light for about 10 minutes.  After that it starts the process over again and reverts back to the green.  No matter what I do the original pod won’t connect to the hub wirelessly.  I was hoping virgin would of requested this one back as an exchange for a working unit.

        Thanks

  • Hi,

    I seem to be having the same issue with both pods.

    They turn on but then starting flashing blue and don’t connect. Also on the connect app when I click on either pod I get the error saying it is not found

    • Arissa_H's avatar
      Arissa_H
      Forum Team

      Hi Janmeet.

      Thank you for posting onto our community forums. Welcoming you with big virtual arms ☺.

      Sorry to see you are having issues connecting your pod.

      Have you manged to connect it since you last spoke to us?

      Thank you.

      • Janmeet's avatar
        Janmeet
        Joining in

        Hi,

        No both pods are still not connecting.

        I now have rooms in my house where we are getting no WiFi at all for example my bedroom, which is making work a bit hard.

  • Rob-Kirsten's avatar
    Rob-Kirsten
    On our wavelength

    So we've recently upgraded to HUB 5 as we have the mega volt bundle with Gig1 fibre, the Hub 5 installed today (Friday 29th September 2023) and already our virgin Intelli wifi pods no longer work, they just cycle the flashing green then blue light repeatedly and now 2 of our slightly older laptops cant even find the network despite both being 802.11n network adaptors connecting via wpa2-Personal AES (Hub3.0)

    Any ideas on how to connect these laptops and sort my wifi pods issues out, btw before anyone says about doing the diagnostics on the pods, been there done that even phoned technical support who claimed there is an issue in my area affecting 25% customer in my area.

    • Paul_DN's avatar
      Paul_DN
      Forum Team

      Hi Rob-Kirsten,

      Thank you for reaching out to us in our community ands welcome, sorry to hear your Pods no longer work since you were upgraded to an Hub 5.0.

      When you say the Pods flash green and blue this isn't something I am aware our pods do,, they generally just show a white light when not connected, you also mentioned the Hub 3.09.

      Can you add a picture of the pods you have, can you also confirm if you have any 3rd part Network equipment such as Router or boosters?

      Regards

      Paul.

    • SmiffyB's avatar
      SmiffyB
      Tuning in


      This worked for me. See the post from Carly-S on 17th April 23

       

  • BeginnersLuck's avatar
    BeginnersLuck
    On our wavelength

    Hi there.

    I’m having exactly the same issue with a WiFi pod I received yesterday: it will flash green for a bit, then blue, then go off for a bit, then start the cycle again. It did it all day, so I turned it off overnight. Have turned it on this morning and no change.

    Having read through this thread, I have tried:

    Rebooting the WiFi router

    Moving the pod into the same room for 15 minutes to see if that helps them connect.

    No matter what I do, the Virgin Connect app will not recognise the pod, and it also seems to have a problem connecting with our router (please see the below screengrab). Every time I try again, it says it’s a problem in Virgin’s side.

    I also tried running a test on my services, but it said it could not run a test right now (screengrab below).

    So now I don’t know if the issue is with the pod or with VM, though I can confirm that I am connected to WiFi while in the same room as the router.

    Can anyone on the VM side help? I need to be able to boost my WiFi to the upstairs of the house, where there is a WiFi black spot where we work.

    Thanks!

    • SmiffyB's avatar
      SmiffyB
      Tuning in

      My issue was solved following advice from Virgin by resetting the router not just rebooting it....have you tried that?

      • BeginnersLuck's avatar
        BeginnersLuck
        On our wavelength

        Sorry, that’s what I should have said first time: I did the pin reset in the back of the router, holding it for 60 seconds.

        I’ve got a Hub 3, if that’s any help.

  • BeginnersLuck's avatar
    BeginnersLuck
    On our wavelength

    OK - a little bit of progress. Out of nowhere, the Connect app started connecting with the router, and it now shows that the two iPhones in the house are connected to WiFi.

    That at least tells me the router and the app are talking to each other, so that’s good. The WiFi pod isn’t showing up on the app, though. I have rebooted it, but I’m still just getting the green light and then the blue flashing light.

  • BeginnersLuck's avatar
    BeginnersLuck
    On our wavelength

    Just another update, for information's sake: laptops, printer, phones are all showing up on the Virgin Connect app when in use, so no problems there. 

    The pod just keeps going through the green/blue light cycle, no presence on the app at all, so it does seem as though the issue is with the pod.

    All these devices (pod included) are in the same room as the router, though in order for the pod to help boost the signal upstairs, I would have to move it into another room - if/when I can get it to work.

    It seems as though the pod is the issue, unless VM have any other ideas?

    Thanks! 

  • BeginnersLuck's avatar
    BeginnersLuck
    On our wavelength

    Hi there, just giving this a little bump, in case a VM team member can help.

    Still not having any luck with connecting the pod - it just keeps flashing blue, in the main. Green comes back along for a bit..

    The hub is at least registering on the Connect app now, but all I get when I try to install the pod is a failure to detect message (screengrab below), which is no surprise as the Connect app doesn’t recognise the pod. I’ve gone to the Help section, as advised, but I’ve not seen much there beyond trying again.

    After 10+ attempts to install, the app told me it needed to optimise my network, which I was hoping would have solved the issue, but after running the optimisation, I’ve still had no luck.

    I have tried resetting the hub a couple of times, as advised above, and also tried connecting the pod in the same room as the hub and also where I really need it (only one room across, so hardly out of range), and neither place works.

    So far, it’s just a white piece of plastic I’ve had since Saturday and now put back in the box. Not a great use of VM’s resources - nor a great result for WiFi improvement.

    But I am hopeful that we can make it work. Is anyone from the VM team able to help me out, please!

    Thank you!

    am hopeful that we can make it work. Is anyone from the VM team able to help take a look at this for me, please?

    Thank you!

    • Matthew_ML's avatar
      Matthew_ML
      Forum Team

      Hey BeginnersLuck, thank you for reaching out and I am so sorry to hear you are having some pod issues.

      Please can you try these steps for me ;

      Unplug any Ethernet cables attached to the router and wait at least 30 seconds, then plug them back in. Plug the router's power cable back into the outlet. Plug the modem back in and wait until the modem has finished powering on. Wait at least 2 minutes for your Pods' LEDs to stop blinking.

      Let us know if that works for you. Cheers 

      • BeginnersLuck's avatar
        BeginnersLuck
        On our wavelength

        Hi, Matthew_ML, thank you for this, I appreciate it.  

        I wasn't sure from the above at what stage I needed to unplug the router's power cable from the outlet, so I went in this order:

        Unplugged all Ethernet cabled attached to the router.

        Unplugged router power cable from outlet.

        Plugged in Ethernet cables.

        Plugged router power cable into outlet.

        Plugged modem back in. 

        This was 25 minutes ago, and unfortunately, the pod is still going through the green/blue cycle. I have tried connecting via the app, for completion's sake, but after optimising the WiFi, the app still says it cannot detect the pod. 

        As I type this, the pod it still flashing blue. 

        What else can we try?

        Thanks!