Hub 4 Ethernet Speed

[thelatman77]

Hey folks, 

Upgraded from my Hub 3 (where I was getting mostly full speed on my 200mb connection) to the Hub 4 and the gig1 package.  Im not getting anywhere near the gig to my devices though on either wifi (where I seem to just about scrape 500mb using Samknows) or ethernet, which is about the same but even worse on my ethernet over power adapters.

I have 3 of these EoP adapters in total; 1x 200mb pair for my hive (dont care what speed that gets)which is in the kitchen, 1x 200mb (used occasionally, atm not connected) and 1x 500mb pair (connected to a Mitel IP phone with a 1gb LAN and 1gb LAN switch port to my laptop (with a 1gb nic) in my office.  I also have a Phillips smart TV connected directly to the router.  OK, these adapters are quite old, but on my Hub 3, I was constantly getting between 180-213mb when testing from the laptop in its normal setup.

I connected my laptop directly to the 1x 500mb adapter, I then checked the speed on SamKnows from my laptop 3 times:

Test 1:

Hub4 - 498, PC - 20.7

Test 2:

Hub4 - 1005, PC - 32.1

Test3

Hub4 - 998, PC - 33.6

I checked the Connected Devices form, it shows all ethernet ports connected at '100'.  When I connected my laptop direct to the Hub ethernet, i get similar Hub4 speeds from Samknows, but slightly higher speeds, the laptop did show as 1000 on the connected devices form though.  Should the ethernet over power adapters show as 200, 200 & 500?

When I test on Wifi, I get similar ranges from Sam knows to the hub, but almost hitting 500 to the PC, I have never gone above 500mb yet.

Just in case, I rebooted the hub last night, powered it off & unplugged it for 3 minutes, then back on.

Does the hub take a few days to throttle up after first activation, or should I be expecting full speeds, or at least better than I was getting on my previous hub / package from day 1?

Cheers,

Lat

[Adduxi]

You need to test a wired connection direct to the Hub with a known good Cat 6 cable. If using Windows, run in Safe Mode with Networking.  PLA's (powerline adapters) are not reliable as they depend on the state of the house wiring etc.  You also need to check that all your IT kit is capable of maintaining a 1GB connection either over wifi or ethernet. 

The 1GB speed does not need a few days to settle, but will be available at the Hub as soon as the configuration file is pushed to the Hub by VM.

[thelatman77]

Hey, thanks for the advice.....I have already tested direct to the ethernet ports with 2 different good cat6 cables and the speeds are still below 500 and well below the gig.

The EoP adapters worked perfectly on my previous hub, the house was built in 95, and the wiring is fine as far as I know (the eop's were working well until this new hub was used), so I don't understand why all of a sudden they all behave so poorly when they have been working well prior to upgrading.

My IT equipment, aside from the eop's (200, 200 & 500mb), are all capable of 1gb connections.

What should the 'Connected Devices' form show for the router side ethernet over power adapters (200mb, 200mb & 500mb)?  atm it shows 100 for each.

[thelatman77]

Network stats:

Cable Modem StatusItem Status CommentsChannel Overview Downstream Upstream

Cable Modem Status	Online	DOCSIS 3.1
Primary downstream channel	Locked	SC-QAM
DOCSIS 3.0 channels	31	4
DOCSIS 3.1 channels	1	0

Channel Frequency (Hz) Power (dBmV) SNR (dB) Modulation Channel ID

25	331000000	2.9	38.6	QAM256	25
1	139000000	3.4	38.6	QAM256	1
2	147000000	3.4	38.6	QAM256	2
3	155000000	3.7	38.6	QAM256	3
4	163000000	3.8	38.6	QAM256	4
5	171000000	3.9	38.6	QAM256	5
6	179000000	3.9	38.6	QAM256	6
7	187000000	4	39	QAM256	7
8	195000000	4.1	39	QAM256	8
9	203000000	3.9	39	QAM256	9
10	211000000	3.8	39	QAM256	10
11	219000000	3.5	38.6	QAM256	11
12	227000000	3.7	39	QAM256	12
13	235000000	3.6	38.6	QAM256	13
14	243000000	3.2	39	QAM256	14
15	251000000	3.1	38.6	QAM256	15
16	259000000	3.3	39	QAM256	16
17	267000000	3.5	39	QAM256	17
18	275000000	3.8	38.6	QAM256	18
19	283000000	3.4	38.6	QAM256	19
20	291000000	3	38.6	QAM256	20
21	299000000	2.5	39	QAM256	21
22	307000000	2.7	39	QAM256	22
23	315000000	3.1	38.6	QAM256	23
24	323000000	3.4	38.6	QAM256	24
26	339000000	2.7	39	QAM256	26
27	347000000	2.7	38.6	QAM256	27
28	355000000	2.2	38.6	QAM256	28
29	363000000	2.2	39	QAM256	29
30	371000000	3	38.6	QAM256	30
31	379000000	3.3	39	QAM256	31

[thelatman77]

3.0 Downstream channels
Channel Lock Status RxMER (dB) Pre RS Errors Post RS Errors
25 Locked 38.605377 0 0
1 Locked 38.605377 0 0
2 Locked 38.605377 0 0
3 Locked 38.605377 0 0
4 Locked 38.605377 0 0
5 Locked 38.605377 0 0
6 Locked 38.605377 0 0
7 Locked 38.983261 0 0
8 Locked 38.983261 0 0
9 Locked 38.983261 0 0
10 Locked 38.983261 0 0
11 Locked 38.605377 0 0
12 Locked 38.983261 0 0
13 Locked 38.605377 0 0
14 Locked 38.983261 0 0
15 Locked 38.605377 0 0
16 Locked 38.983261 0 0
17 Locked 38.983261 0 0
18 Locked 38.605377 0 0
19 Locked 38.605377 0 0
20 Locked 38.605377 0 0
21 Locked 38.983261 0 0
22 Locked 38.983261 0 0
23 Locked 38.605377 0 0
24 Locked 38.605377 0 0
26 Locked 38.983261 0 0
27 Locked 38.605377 0 0
28 Locked 38.605377 0 0
29 Locked 38.983261 0 0
30 Locked 38.605377 0 0
31 Locked 38.983261 0 0



3.1 Downstream channels
Channel Channel Width (MHz) FFT Type Number of Active Subcarriers Modulation (Active Profile) First Active Subcarrier (Hz)
33 96 4K 1880 QAM4096 759


3.1 Downstream channels
Channel ID Lock Status RxMER Data (dB) PLC Power (dBmV) Correcteds (Active Profile) Uncorrectables (Active Profile)
33 Locked 41 4.8 84431840 0

[thelatman77]

3.0 Upstream channels

Channel Frequency (Hz) Power (dBmV) Symbol Rate (ksps) Modulation Channel ID

1	32600000	38	5120 KSym/sec	64QAM	10
2	39400000	37.5	5120 KSym/sec	64QAM	9
3	46200000	37.3	5120 KSym/sec	32QAM	8
4	53700000	37.3	5120 KSym/sec	64QAM	7

3.0 Upstream channels

Channel Channel Type T1 Timeouts T2 Timeouts T3 Timeouts T4 Timeouts

1	US_TYPE_STDMA	0	0	0	0
2	US_TYPE_STDMA	0	0	0	0
3	US_TYPE_STDMA	0	0	0	0
4	US_TYPE_STDMA	0	0	0	0

[thelatman77]

General Configuration
Network access
true
Maximum Number of CPEs
1
Baseline Privacy
true
DOCSIS Mode
3.1
Config file
cmreg-vmdg640-bbt076+voc-b.cm


Primary Downstream Service Flow
SFID
378516
Max Traffic Rate
1200000450
Max Traffic Burst
42600
Min Traffic Rate
0


Primary Upstream Service Flow
SFID
378515
Max Traffic Rate
55000270
Max Traffic Burst
42600
Min Traffic Rate
0
Max Concatenated Burst
42600
Scheduling Type
bestEffort

[legacy1]

---

@thelatman77 wrote:

My IT equipment, aside from the eop's (200, 200 & 500mb), are all capable of 1gb connections.

test without eop's on a wired connection

and test speed in modem mode with a PC.

[thelatman77]

Hey, as I said in my OP, I have tested using the ethernet ports on the back of the router, I'll try modem mode.

It's actually slower than my 200mb package, according to samknows..

[Roger_Gooner]

You might have a problem on upstream channel 3. Wait for a forum team member to assist.