on 09-12-2021 17:32
Hi
I have recently upgraded from Ultimate Oomph to Ultimate Volt With Gig1 available in my area
The Hub 4 Self Install kit arrived and was installed on Saturday evening (04/12)
I have noticed that the upload and download speeds are consistent with M600 and are not going any higher than 644.91mbps Down / 42.09 mbps Up
Having a look at the Downstream/Upstream channels in the Router Logs of the Hub 4 , There is only 1 DOCSIS 3.1 Downstream channel and There is no DOCSIS 3.1 Upstream channels
DOCSIS 3.0 However has 31 Downstream and 4 Upstream - is this correct?
I have today powered off and on Hub 4 since it was installed on Saturday, Thinking perhaps due to the day and time of install may of delayed the changes on the line for Gig1 but the speed remains the same.
If anyone could please advise me?
Thanks,
R
on 09-12-2021 17:49
Sounds like the upgrade hasn't gone through
on 09-12-2021 17:59
VM currently only use a single D3.1 downstream channel, and none upstream, that won't change when you get the speed enabled.
That you're seeing the D3.1 channel means you're using a Hub 4 and in a D3.1 enabled area, so sounds like you're just waiting for the new config file to be pushed to the hub.
on 09-12-2021 19:36
Thanks Andrew-G
Do you know when the new config file is likely to be pushed to the Hub 4 or is it something I'm going to have to call customer support and enquire about?
09-12-2021 21:04 - edited 09-12-2021 21:05
@robw95 wrote:Thanks Andrew-G
Do you know when the new config file is likely to be pushed to the Hub 4 or is it something I'm going to have to call customer support and enquire about?
If you log into the HUB and access the 'Advanced Settings \ Tools \ Network Status' section, under the 'Configuration' tab you should see the current config:
Network access | true |
Maximum Number of CPEs | 1 |
Baseline Privacy | true |
DOCSIS Mode | 3.1 |
Config file | 54k;fg87dsfd;kfoA,.iyewrk |
SFID | 889 |
Max Traffic Rate | 1200000450 |
Max Traffic Burst | 42600 |
Min Traffic Rate | 0 |
SFID | 1420 |
Max Traffic Rate | 55000270 |
Max Traffic Burst | 42600 |
Min Traffic Rate | 0 |
Max Concatenated Burst | 16320 |
Scheduling Type | bestEffort |
on 10-12-2021 12:00
Thanks carl_pearce,
The config file and the Max Traffic Rate on both the Downstream and Upstream Service Flow are different from your example.
I'm guessing this means that the configuration hasn't been updated to reflect the change to Gig1.
Network access | true |
Maximum Number of CPEs | 1 |
Baseline Privacy | true |
DOCSIS Mode | 3.1 |
Config file | cmreg-vmdg640-bbt078+voc-b.cm |
SFID | 7058 |
Max Traffic Rate | 690000278 |
Max Traffic Burst | 42600 |
Min Traffic Rate | 0 |
SFID | 7057 |
Max Traffic Rate | 44000278 |
Max Traffic Burst | 42600 |
Min Traffic Rate | 0 |
Max Concatenated Burst | 42600 |
Scheduling Type | bestEffort |
on 10-12-2021 14:28
Your config file is for 600. Time to call VM?
I'm a Very Insightful Person, I'm here to share knowledge, I don't work for Virgin Media. Learn more
Have I helped? Click Mark as Helpful Answer or use Kudos to say thanks
on 12-12-2021 10:53
Thanks carl_pearce, after waiting nearly an hour on chat this morning I was able to tell them that the primary and upstream numbers were still configured for M600 and after a few minutes they were changed to the correct values for Gig1 and now seeing a speed increase (although Speedtest still maxing out around 700Mbps). Will monitor over the next few days.
on 12-12-2021 10:56
@starlir wrote:Thanks carl_pearce, after waiting nearly an hour on chat this morning I was able to tell them that the primary and upstream numbers were still configured for M600 and after a few minutes they were changed to the correct values for Gig1 and now seeing a speed increase (although Speedtest still maxing out around 700Mbps). Will monitor over the next few days.
What does this site show?
https://samknows.com/realspeed/
on 12-12-2021 11:08
Carl, I'm in modem mode so the Samknows agent can't find it. Is there any way round that?