Menu
Reply
  • 420
  • 19
  • 85
tonycv51
Fibre optic
1,052 Views
Message 4231 of 4,479
Flag for a moderator

Re: Hub 3 / Compal CH7465-LG (TG2492LG) and CGNV4 Latency Cause


@tonycv51 wrote:

Can someone please confirm that they’ve got the update in modem mode automatically ie without pin hole reset and running in router mode temporarily. If so was that 350 or also other packages. ?  And finally was the SH3 still in modem mode after the update ?


Thanks for the various replies, and warnings about switching modes. I’ll leave mine in modem mode and wait impatiently to be blessed with the new firmware. 

0 Kudos
  • 44
  • 3
  • 10
Connect123
Dialled in
1,019 Views
Message 4232 of 4,479
Flag for a moderator

Re: Hub 3 / Compal CH7465-LG (TG2492LG) and CGNV4 Latency Cause

Sounds awesome , purchased a Netgear r7000 nighthawk yesterday, hopefully that going into the superhub 3 in modem mode and the new firmware will be a good combo

0 Kudos
  • 38
  • 0
  • 6
fat4l
On our wavelength
821 Views
Message 4233 of 4,479
Flag for a moderator

Re: Hub 3 / Compal CH7465-LG (TG2492LG) and CGNV4 Latency Cause

Ok guys. A few questions:

1. What is the latest/the latest beta bios used ? I have "9.1.116.608"
2. I have 350Mbit. On cable it does 388Mbit but wifi coverage of SH3 is poor and my PC is far so I dont get full speed. If I go with "Modem Mode" what router is a good one to use, with
......A) Good wifi coverage(better than SH3)
......B) Good for gaming
......C) Support full 388MBit speed on 5G wifi
......D) Does not cost 250£+ lol
......E) yes I know wifi is not for gaming, I'm going cable in the future
3. If I buy a new router+modem mode, what sort of "benefits" or improvements will I get/feel ?
4. What happens if you connect some other router to one of the ethernet cables and leave your SH3 in router mode ? Will you get like double wifi + more ports?

Thanks

0 Kudos
  • 51
  • 0
  • 10
Loui79
On our wavelength
808 Views
Message 4234 of 4,479
Flag for a moderator

Re: Hub 3 / Compal CH7465-LG (TG2492LG) and CGNV4 Latency Cause

1 You've got it
2 pretty much any router with QoS over £50 will be better than the Hub 3. The speed you get will depend on distance etc
3 depends what router you get. most have more features and are more configurable
4 Double NAT for gaming unless you put the second router in DMZ or run it as an AP. Running in DMZ you'd have 2 different networks. Running in AP, you're wasting the benefits of the router.
0 Kudos
  • 24
  • 0
  • 2
lynxblaine
Tuning in
763 Views
Message 4235 of 4,479
Flag for a moderator

Re: Hub 3 / Compal CH7465-LG (TG2492LG) and CGNV4 Latency Cause

Definitely a new router would help.

You could make sure that the 5GHz channel width is set to 20/40/80 MHz rather than just 20/40 it is set to default. That got me from about 170Mbps up to 210Mbps on my 200 package on my phone .

0 Kudos
  • 52
  • 0
  • 4
risc19
Dialled in
746 Views
Message 4236 of 4,479
Flag for a moderator

Re: Hub 3 / Compal CH7465-LG (TG2492LG) and CGNV4 Latency Cause

So, does everyone have the update now?

I'm still waiting.

0 Kudos
  • 44
  • 3
  • 10
Connect123
Dialled in
747 Views
Message 4237 of 4,479
Flag for a moderator

Re: Hub 3 / Compal CH7465-LG (TG2492LG) and CGNV4 Latency Cause

Still waiting for mine, area 31

  • 62
  • 2
  • 17
hammic
Dialled in
725 Views
Message 4238 of 4,479
Flag for a moderator

Re: Hub 3 / Compal CH7465-LG (TG2492LG) and CGNV4 Latency Cause


@risc19 wrote:

So, does everyone have the update now?

I'm still waiting.


I had the update, then my factory reset downgraded me to 116v again.

  • 53
  • 0
  • 7
anTastico
On our wavelength
714 Views
Message 4239 of 4,479
Flag for a moderator

Re: Hub 3 / Compal CH7465-LG (TG2492LG) and CGNV4 Latency Cause

Still waiting, area 26.

Highlighted
  • 38
  • 0
  • 6
fat4l
On our wavelength
657 Views
Message 4240 of 4,479
Flag for a moderator

Re: Hub 3 / Compal CH7465-LG (TG2492LG) and CGNV4 Latency Cause

and guys what is this "9.1.116.608" firmware fixing exactly ? No more latency spikes ?

0 Kudos